[수입판매] Pepperl + Fuchs Thru-beam sensor OBE40M-R200-S2EP-IO-V1-L 포토센서

[수입판매] Pepperl + Fuchs Thru-beam sensor OBE40M-R200-S2EP-IO-V1-L 포토센서

• 다양한 장착 옵션이 있는 중간 디자인
• DuraBeam 레이저 센서 - 내구성이 뛰어나고 LED처럼 사용 가능
• 서비스 및 프로세스 데이터용 IO-Link 인터페이스
• 상호 간섭 방지를 위한 다양한 주파수(누화 내성)
• 확장된 온도 범위 -40°C ... 60°C
• 높은 보호 등급 IP69K

System components
Emitter		OBE40M-R200-S-IO-V1-L
Receiver		OBE40M-R200-2EP-IO-V1-L
General specifications
Effective detection range		0 ... 40 m
Threshold detection range		50 m
Light source		laser diode
Light type		modulated visible red light
Laser nominal ratings
	Note	LASER LIGHT , DO NOT STARE INTO BEAM
	Laser class	1
	Wave length	680 nm
	Beam divergence	> 5 mrad ; d63 < 2 mm in the range of 250 mm ... 750 mm
	Pulse length	1.6 µs
	Repetition rate	max. 17.6 kHz
	max. pulse energy	9.6 nJ
Alignment aid		LED red (in receiver lens) illuminated constantly: beam is interrupted, flashes: reaching switching point, off: sufficient stability control
Diameter of the light spot		approx. 80 mm at a distance of 40 m
Opening angle		approx. 0.12 °
Ambient light limit		EN 60947-5-2 : 40000 Lux
Functional safety related parameters
MTTFd		440 a
Mission Time (TM)		20 a
Diagnostic Coverage (DC)		60 %
Indicators/operating means
Operation indicator		LED green: constantly on - power on flashing (4Hz) - short circuit flashing with short break (1 Hz) - IO-Link mode
Function indicator		Yellow LED: Permanently lit - light path clear Permanently off - object detected Flashing (4 Hz) - insufficient operating reserve
Control elements		Receiver: light/dark switch
Control elements		Receiver: sensitivity adjustment
Electrical specifications
Operating voltage		10 ... 30 V DC
Ripple		max. 10 %
No-load supply current		Emitter: ≤ 13 mA Receiver: ≤ 15 mA at 24 V Operating voltage
Protection class		III
Interface
Interface type		IO-Link ( via C/Q = pin 4 )
IO-Link revision		1.1
Device profile		Identification and diagnosis Smart Sensor: Receiver: type 2.4 Emitter: -
Device ID		Emitter: 0x111402 (1119234) Receiver: 0x111302 (1118978)
Transfer rate		COM2 (38.4 kBit/s)
Min. cycle time		2.3 ms
Process data width		Emitter: Process data input: 0 bit Process data output: 1 bit Receiver: Process data input: 2 bit Process data output: 2 bit
SIO mode support		yes
Compatible master port type		A
Input
Test input		emitter deactivation at +UB
Output
Switching type		The switching type of the sensor is adjustable. The default setting is: C/Q - Pin4: NPN normally open / dark-on, PNP normally closed / light-on, IO-Link /Q - Pin2: NPN normally closed / light-on, PNP normally open / dark-on
Signal output		2 push-pull (4 in 1) outputs, short-circuit protected, reverse polarity protected, overvoltage protected
Switching voltage		max. 30 V DC
Switching current		max. 100 mA , resistive load
Usage category		DC-12 and DC-13
Voltage drop		≤ 1.5 V DC
Switching frequency		1250 Hz
Response time		0.4 ms

​

​

​